16 mm carburetor suitable for your Honda Camino PA50 M moped / moped.
The carburetor, which is also available under the designation BB20b, is completely ready for installation including choke lever and O-ring for sealing at the flange surface. Even a 30 cm long overflow hose is included.
Further parts for your Honda Camino can be found in the accessories section.
| Nominal diameter | 16 mm |
| Width | 75 mm |
| Material | Aluminum |
| Component group Carburetor | Carburetor complete |
| Total length | 85 mm |
| Ø fuel hose connection | 5 mm |
| Height | 90 mm |
| Ø Internal connection | 16 mm |
| Ø Output inside | 27.4 mm |
| Hole spacing inlet | 42.5 mm |
| Mounting type | Stud bolts & nuts |
| Vacuum connection | No |
| Camouflaged | No |
| Honda |
Ratings
Accessories & related products
Autisa 44 mm cylinder kit NOS | Honda Camino
Manufacturer: Autisa · Material: Gray cast iron · Surface: varnished · Nominal diameter: 44 mm · Camouflaged: No · Area of application: Tuning · Ø piston pin (B): 10 mm · Number of fixing points: 4 pcs · Outlet type: slanted · Thread outlet: M6x1 (standard thread)
EUR 82.80
Malossi nozzle tuning set 45.5 mm cylinder | Honda Camino, PX
Manufacturer: Malossi · Component group Carburetor: Spraying · Material: Brass · Material: HSS · Quantity: 2 pcs · Nozzle type: Main nozzle · Nozzle thread: MF7x0.8 (fine pitch thread) · Nozzle size: 78 · Nozzle size: 90 · Thread length: 5.8 mm · Drive: Slot · Total length: 8.5 mm
EUR 14.80
Moped fans also bought
Hot 
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø nipple: 3 mm · Nipple length: 5 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Ø Stranded wire: 1.25 mm · Cable length: 2200 mm · Nipple shape: Cylinder · Area of application: Standard
EUR 2.85
Hot
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Cable length: 2200 mm · Area of application: Standard
EUR 2.85
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Ø inside: 12 mm · Width: 8 mm · Ø outside: 28 mm · Area of application: Standard
EUR 7.00
Autisa 44 mm cylinder kit NOS | Honda Camino
Manufacturer: Autisa · Material: Gray cast iron · Surface: varnished · Nominal diameter: 44 mm · Camouflaged: No · Area of application: Tuning · Ø piston pin (B): 10 mm · Number of fixing points: 4 pcs · Outlet type: slanted · Thread outlet: M6x1 (standard thread)
EUR 82.80
External ignition coil with capacitor | Honda Camino
Place of use: Ignition · Cable length: 400 mm · Color: black · Total length: 100 mm · Height: 40 mm · Height: 70 mm · Mounting type: Nuts & bolts · Number of fixing points: 2 pcs · Ø mounting hole: 6 mm · Hole spacing: 60 mm · Area of application: Standard
EUR 39.00
Collection only possible with online purchase and appointment.
