Stage6 adapter intake manifold Mikuni carburetor 24 mm

Sealing paper set 4 pcs.

Place of use: Universal · Thickness: 0.25 mm · Thickness: 0.4 mm · Thickness: 0.5 mm · Thickness: 1.2 mm · Manufacturer: Made in Spain · Material: Sealing carton · Material: Sealing paper

MIKUNI 24 mm flat slide carburetor TM24-9 hand choke

Manufacturer: MIKUNI · Component group Carburetor: Carburetor complete · Carburetor type: Flat slide valve · Nominal diameter: 24 mm · Choke control: Hand choke · Width: 75 mm · Height: 130 mm · Ø Air filter connection: 44 mm · Area of application: Tuning · Ø fuel hose connection: 6 mm · Nozzle thread: M5.3x0.9 (standard thread) · Nozzle size: 130 · Size of secondary nozzle: 51 · Mounting type: Plug connection

Athena Athesil sealing compound gray (silicone) 80 ml permanently elastic up to 300 °C

Manufacturer: Athena · Material: Silicone · Color: gray · Contents: 80 ml · Temperature resistance (min.): -40 - 300 °C · Area of application: Chemistry

Stage6 reed valve block VForce 3 by Moto Tassinari

Manufacturer: Stage6 · Number of flaps: 8 pcs · Hole spacing: 52 mm

Stage6 adapter intake manifold Dell'Orto / Polini CP carburetor 21 mm

Ø inside: 21 mm · Manufacturer: Stage6 · Material: Rubber · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold PWK carburetor 19 - 28 mm

Ø inside: 30 mm · Ø inside: 33 mm · Manufacturer: Stage6 · Material: Rubber · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold PWK carburetor from 30 mm

Ø inside: 35 mm · Ø inside: 40 mm · Manufacturer: Stage6 · Material: Rubber · Hole spacing inlet: 60 mm

Heat protection tape with fastening blue 5 m

Total length: 5000 mm · Material: Chrome steel (colloquially known as stainless steel) · Material: Fiber · Color: blue · Thickness: 1.5 mm · Width: 50 mm

ADDY engine housing GME "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

ADDY engine housing GME spindled "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

Intake manifold 25 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Ø inside: 25 mm · Hole pattern [mm]: 55 / 60

Intake manifold 29 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Ø inside: 29 mm · Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Hole pattern [mm]: 55 / 60

Gilardoni italkit 47 mm cylinder kit 75 ccm | Puch

Manufacturer: Gilardoni italkit · Camouflaged: No · Area of application: Tuning · Material: Aluminum · Surface: sandblasted · Nominal diameter: 47 mm · Outlet type: slanted · Decompressor: No

Speedometer 60 km/h Ø 48 mm black / chrome

Manufacturer: Made in Germany · Depth: 50 mm · Material: Metal · Material: Plastic · Color: Chrome · Color: black · Surface: chrome-plated · Color: red · Color: white · Ø Receptacle: 48 mm · Thread type: MF10x1 (fine pitch thread) · Maximum speed: 60 Km/h · Lighting: Light slit · Signal type Tacho: analog · 4-edge speedometer cable: 1.8 mm · Ø outside: 50.4 mm · Total height: 70 mm

GPO mushroom air filter grille chrome 28 - 32 mm

Manufacturer: GPO · Mounting type: Bride · Mounting type: Plug connection clamped · Material: Metal · Camouflaged: No · Material: Rubber · Area of application: Tuning · Color: Chrome · Color: black · Filter type: Grille · Total length: 115 mm · Ø Internal connection: 28 mm · Ø Internal connection: 32 mm · Length rubber part: 65 mm · Length of filter section: 50 mm · Ø outside: 61 mm

Polini jet set (140 - 158) main jets long version CP, Keihin, Koso, PWK

Manufacturer: Polini · Material: Brass · Quantity: 10 pcs · Component group Carburetor: Spraying · Carburetor type: CP · Carburetor type: Coso · Drive: External hexagon · Carburetor type: Keihin · Carburetor type: PWK · Nozzle type: Main nozzle · Nozzle size: 140 · Nozzle size: 142 · Nozzle size: 144 · Nozzle size: 146 · Nozzle size: 148 · Nozzle size: 150 · Nozzle size: 152 · Nozzle size: 154 · Nozzle size: 156 · Nozzle size: 158

Stage6 reed valve block VForce 3 by Moto Tassinari

Manufacturer: Stage6 · Number of flaps: 8 pcs · Hole spacing: 52 mm

ADDY engine housing GME spindled "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

Membrane box for ADDY GME engine housing "der.pruefstand" | Puch E50

Total length: 48 mm · Material: Aluminum · Width: 66 mm · Hole pattern [mm]: 37 x 55 · Hole spacing: 52 mm · Thread type: M6x1 (standard thread)

Intake manifold 29 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Ø inside: 29 mm · Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Hole pattern [mm]: 55 / 60

ADDY engine housing set GME "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

Transval speedo drive 16" with grease nipple | Pony Cross 521 (P8281A)

Manufacturer: Transval · Material: Aluminum · Wheel size: 16 " · 4-edge speedometer cable: 2.6 mm · Ø axle: 11 mm · Ø mounting hole: 11 mm · Ø outside: 41 mm · Place of use: left · Place of use: right · Thread type: MF10x1 (fine pitch thread) · Pony OEM number: P8281A