Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with a Selettra license plate.
Made in Switzerland. Designed for the highest loads and proven in racing.
Mounting:
- Starter pinion: Clean the Selettra pole wheel, then screw the counterpart for the cable starter onto the pole wheel (secure the enclosed screws with Loctite).
- Pull starter: Position the starter housing in the correct position and tap lightly with a plastic hammer until the pull starter is perfectly seated. It can then be screwed into place.
Application:
- Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
- Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Further helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber hammer etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
Details
| Surface | chrome-plated |
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Ignition system | Selettra |
| Number of fixing points | 2 pcs |
| Color | Chrome |
Suitable for the following models
| Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Color: blue · Contents [ml]: 10 ml · Area of application: Chemistry · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 25.90
EUR 2’590.00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Manufacturer: GPO · Material: Steel · Surface: chrome-plated · Chain pitch: 1/2" x 3/16" · Number of teeth: 28 pcs · Total length: 257 mm · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø outside: 15.9 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Color: Chrome · Crank (wreath): 7.5 mm
EUR 70.90
swiing® ingenious screw M6x25 special drive pinion pull rope starter PVL, Selettra
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® ingenious parts · Total length: 25 mm · Drive: Hexagon socket · Thread type: M6x1 (standard thread) · Screw head: Countersunk head · Width across flats SW: 4 mm · Strength class: 10.9
EUR 3.40
Moped fans like you also bought:
MLM 25 mm intake manifold Gilardoni italkit black | Puch
Manufacturer: MLM · Material: Steel · Area of application: Tuning · Surface: varnished · Color: black · Number of fixing points: 4 pcs · Ø inside: 25 mm · Ø External connection: 28.5 mm · Mounting type: Screws · Hole pattern [mm]: 60 x 35
EUR 94.60
Manual indoor cable set
Total length: 2200 mm · Ø Stranded wire: 1.2 mm · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs
EUR 11.70
Inner cable set automatic | Puch E50
Total length: 1600 mm · Total length: 2200 mm · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs
EUR 11.70
Manual cable set black
Material: Steel · Total length: 2200 mm · Ø Stranded wire: 1.2 mm · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Quantity: 4 pcs · Outer shell length: 6000 mm · Color: black
EUR 23.60
swiing® revival screw set Motor Inox | Puch E50
Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Area of application: Standard · Surface: blank · Drive: Hexagon socket · Drive: Slot · Screw head: Countersunk head · Screw head: Cylinder head · Puch OEM number: 900.1216 · Puch OEM number: 900.1308
EUR 23.60
swiing® ingenious crankshaft High End C3/4 & FPM (+1 mm stroke) (Version 2.0) | Puch E50
Material: Steel · Manufacturer: swiing® ingenious parts · Area of application: High End · Cheek type: Full cheeks · Thread type: MF10x1 (fine pitch thread) · Crankshaft stroke: 44 mm · Thread length: 11 mm · Thread length: 15 mm · Connecting rod length center-center: 90 mm · Number of gears: 1 pcs · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø piston pin (B): 12 mm · Ø Bearing seat (clutch side): 17 mm · Weight: 970 g · Ø Bearing seat (ignition side): 17 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm
EUR 272.20
Collection only possible with online purchase and appointment.
