Wheel axle set with closed groove ball bearings for front wire spoke wheels on your Puch moped / moped.
The set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The innovation set works with spoke hubs (spoke rims).
The cable ties show you where to mount what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable ties: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to ensure that the long spacer between the two ball bearings is mounted without play to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
Details
| Ø inside | 12 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel |
| Surface | galvanized (blue) |
| Ø shaft | 11.95 mm |
| Shank length | 74.5 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Total length | 165 mm |
| Thread length | 40.5 mm, 50 mm |
| Width across flats SW | 19 mm |
| Width | 35.7 mm, 6.6 mm, 11 mm, 2.7 mm |
| Height | 9.9 mm, 5.9 mm |
| Ø outside | 29.02 mm |
| Ball bearing closed | Yes |
Suitable for the following models
| Puch |
Accessories & related products
Nut M12x1 x 10 SW19 Wheel nut galvanized
Material: Steel · Surface: galvanized (blue) · Area of application: Standard · Drive: External hexagon · Nut type: Hexagon nut · Thread type: MF26x1 (fine pitch thread) · Height: 10 mm · Thread depth: 10 mm · Width across flats SW: 19 mm · Strength class: 8
EUR 2.35
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Ø inside: 12 mm · Manufacturer: swiing® ingenious parts · Total length: 190 mm · Material: Steel · Surface: galvanized (blue) · Ø shaft: 19 mm · Diameter: 29 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats SW: 19 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Ball bearing closed: Yes · Ø outside: 29 mm
EUR 46.10
Not in stock
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 9 mm · Ø inside: 12 mm · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Material: Plastic · Material: Steel · Surface: blank · Bearing type: Deep groove ball bearing · Width: 9 mm · Ball bearing closed: Yes · Ø outside: 29.02 mm
EUR 10.50
swiing® revival wheel nut M12x1 x 4 SW17 galvanized
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Drive: External hexagon · Nut type: Hexagon nut · Thread type: MF12x1 (fine pitch thread) · Height: 4 mm · Width across flats SW: 17 mm · Strength class: 8
EUR 3.40
66HEROES pointed nut "Spike" M12 Inox
Manufacturer: 66HEROES · Material: Chrome steel (known as Nirosta®) · Drive: External hexagon · Nut type: Pointed nut · Thread type: M10x1.5 (standard thread) · Thread type: M12x1.75 (standard thread) · Thread type: M5x0.8 (standard thread) · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread)
EUR 8.15
swiing® ingenious wheel axle with bearing conversion kit cast hub front Ø 29 mm | Puch
Ø inside: 12 mm · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 40.5 mm · Thread length: 50 mm · Total length: 165 mm · Width across flats SW: 19 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 34.5 mm · Height: 5.9 mm · Height: 9.9 mm · Ball bearing closed: Yes · Ø outside: 29.02 mm
EUR 46.10
Moped fans like you also bought:
Fuel tap horizontal M12x1 (with union nut) outgoing at the bottom
Possible lever positions: open / closed / reserve · Material lever: Metal · Thread type: MF12x1 (fine pitch thread) · Filter type: Plastic net · Installation direction: horizontal / horizontal · Outlet direction: below · Spare tube shape: curved · Ø fuel hose connection: 6 mm · Reserve level: 70 mm · Mounting type: Union nut
EUR 11.70
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Valve type: TR4 Auto valve · Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Tire height [%]: 100 · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 "
EUR 11.70
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Nipple length: 14 mm · Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Surface: raw · Color: silver · Quantity: 36 pcs · Length from hook: 188 mm · Nominal diameter (thread): 3.15 mm · Thread length: 11 mm · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 °
EUR 65.00
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Ø inside: 12 mm · Manufacturer: swiing® ingenious parts · Total length: 190 mm · Material: Steel · Surface: galvanized (blue) · Ø shaft: 19 mm · Diameter: 29 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats SW: 19 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Ball bearing closed: Yes · Ø outside: 29 mm
EUR 46.10
Not in stock
Inner cable set automatic | Puch E50
Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Total length: 1600 mm · Total length: 2200 mm
EUR 11.70
Collection only possible with online purchase and appointment.
