Chrome-plated racing exhaust with attached silencer suitable for various Puch mopeds / mopeds with a straight outlet.
This tuning exhaust delivers plenty of power and is also visually stunning.
The rearmost end of the resonance body is fitted with a screw. Two additional screws with different holes are included in the scope of delivery.
These can be replaced. This changes the exhaust back pressure and therefore the performance of the silencer.
This gives you an exhaust for the lower, middle and upper speed range all in one.
You can find more racing pipes in the accessories section.
Branded product from the Portuguese manufacturer TECNO.
| Manufacturer | TECNO |
| Material | Steel, Aluminum |
| Surface | chrome-plated |
| Color | Chrome |
| Total length | 900 mm |
| Ø Silencer | 60 mm |
| Ø Internal connection | 24 mm |
| Ø Flame tube outside | 28 mm |
| Exhaust type | Cone / double cone |
| Number of fixing points | 3 pcs |
| Puch |
Ratings
Accessories & related products
swiing® ingenious gasket outlet 28 mm graphite
Manufacturer: swiing® ingenious parts · Place of use: Exhaust · Material: Graphite / Graphite · Thickness: 3 mm · Reinforced: No · Ø outlet inside: 28 mm · Ø screw holder: 6.6 mm · Ø inside: 27.4 mm · Hole spacing outlet: 42.5 mm · Area of application: Tuning
EUR 8.75
Hot 
HOMOET exhaust P6 blank | Puch
Manufacturer: HOMOET · Material: Steel · Color: gray · Surface: raw · Surface: varnished · Ø Silencer: 50 mm · Flame tube attachment: Stud bolts & nuts · Mounting type: Tab · Ø outside: 88 mm · Total length: 900 mm · Ø Flame tube outside: 28 mm · Exhaust type: Cone / double cone · Number of fixing points: 2 pcs
EUR 337.60
Not in stock
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Color: Chrome · Color: black-matt · Surface: chrome-plated · Ignition system: BOSCH · Ignition system: DUCATI · Width: 150 mm · Height: 88 mm · Ø outside: 130 mm · Total length: 160 mm · Number of fixing points: 2 pcs · Hole spacing: 137.5 mm
EUR 177.60
Not in stock
Not so nice 
Road Master 2.25 x 17" F-323 4.P.R. Allround
Manufacturer: Road Master · Tire width: 2.25 " · Color: black · Width: 2 1/4 " · Old designation: 21 x 2.25 " · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: F-323 4.P.R. · Tire type: Allround · White wall: No · Wheel size: 17 " · Tubeless (yes/no): Tubetype TT (requires hose)
EUR 38.50
swiing® revival brake support bolt short Inox | Puch Maxi, Supermaxi
Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Number of components: 3 pcs · Ø shaft: 9.8 mm · Drive: Outer edge · Total length: 32 mm · Ø External head: 14 mm · Thread type: MF10x1 (fine pitch thread) · Shank: Yes · Shank length: 9.5 mm · Width across flats: 13 mm · Thread length: 13 mm · Width across flats: 17 mm · Area of application: Standard
EUR 15.30
Hot
Jammer racing clutch special 65 ccm and more | Puch E50
Manufacturer: Jammer · Material: Steel · Material addition: Steel · Recording type: Cone mounting · Number of jaws: 3 pcs · Thickness: 19 mm · Ø outside: 92.5 mm · Number of springs: 3 pcs · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning
EUR 225.00
Not in stock
Hot
swiing® ingenious 15 mm carburetor camouflaged | Puch
Nominal diameter: 15 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Width: 50 mm · Carburetor type: SRE · Height: 95 mm · Total length: 66 mm · Ø Internal connection: 20 mm · Ø Inside entrance: 15 mm · Ø Output inside: 15 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 20 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.17 · Nozzle size: 62 · Area of application: Tuning · Clamping screw torque (max.): 4 N/m · Puch OEM number: 349.1.15.100.0 · Puch OEM number: 349.2.15.800.0 · Puch OEM number: 349.4.15.500.0 · Puch OEM number: 349.4.15.000.0 · Puch OEM number: 349.4.15.300.0 · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0 · Puch OEM number: 349.8.15.400.0 · Puch OEM number: 349.9.15.300.0
EUR 94.70
Hot
swiing® revival 12 mm carburetor "Original" | Puch
Nominal diameter: 12 mm · Manufacturer: swiing® revival parts · Material: Aluminum · Camouflaged: No · Component group Carburetor: Carburetor complete · Color: gray · Width: 50 mm · Carburetor type: SRE · Height: 108 mm · Total length: 65 mm · Ø Internal connection: 20 mm · Ø Inside entrance: 12 mm · Ø Output inside: 12 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 20 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.15 · Nozzle size: 52 · Area of application: Standard · Clamping screw torque (max.): 4 N/m · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0
EUR 82.80
Collection only possible with online purchase and appointment.
