Storage

swiing® revival wheel bearing 25/37/6.3 coaster wheel

Bearing type: Ball ring · Bearing cage: "-" Sheet steel cage ball-guided · Stock number: K042 · Inner ring width: 25 mm · Ball bearing closed: No · Manufacturer: swiing® revival parts · Groove ring: No · Material: Steel · Ø ball: 6.34 mm · Width: 6.8 mm · Ø outside: 36 mm · Ø inside: 25 mm · Area of application: Standard

NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi

Bearing type: Deep groove ball bearing · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm

swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi

Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 9 mm · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Material: Plastic · Material: Steel · Bearing type: Deep groove ball bearing · Width: 9 mm · Ø outside: 29.02 mm · Surface: blank · Ø inside: 12 mm · Ball bearing closed: Yes

swiing® revival 7/32" balls Ø 5.56 mm (22 pcs.)

Ø ball [inch] / [mm]: 7/32" (5.56 mm) · Manufacturer: swiing® revival parts · Surface: hardened & ground · Material: Steel · Number of components: 22 pcs · Area of application: Standard

swiing® revival bearing cone M11x1

Manufacturer: swiing® revival parts · Surface: gas nitrided · Color: black · Thread type: MF11x1 (fine pitch thread) · Ø outside: 17.95 mm · Height: 14.15 mm · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 7/32" (5.56 mm)

swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch

Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 19 mm · Diameter: 29 mm · Shank length: 100 mm · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29 mm · Thread length: 29 mm · Thread length: 53 mm · Ø inside: 12 mm · Width across flats SW: 19 mm · Total length: 190 mm · Ball bearing closed: Yes

Bearing cone M11x1 mm

Material: Steel · Surface: gas nitrided · Color: graphite colors · Thread type: MF11x1 (fine pitch thread) · Ø outside: 19 mm · Height: 12 mm · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Ø ball [inch] / [mm]: 3/16" (4.78 mm) · Ø ball [inch] / [mm]: 7/32" (5.56 mm)

CUBE 6001 2RS wheel bearing 12/28x8 rear cast hub Leleu black | Puch Maxi

Stock number: 6001 · Inner ring width: 8 mm · Manufacturer: CUBE · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard · Bearing type: Deep groove ball bearing · Ø outside: 28 mm · Ø inside: 12 mm · Width: 8 mm · Ball bearing closed: Yes

swiing® ingenious wheel axle with bearing conversion kit cast hub front Ø 29 mm | Puch

Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29.02 mm · Thread length: 40.5 mm · Thread length: 50 mm · Ø inside: 12 mm · Height: 5.9 mm · Height: 9.9 mm · Width across flats SW: 19 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 34.5 mm · Ball bearing closed: Yes

swiing® revival dust ring wheel bearing Ø 29.3 / 18.6 mm | Puch

Manufacturer: swiing® revival parts · Ø outside: 29.3 mm · Ø inside: 18.6 mm · Puch OEM number: 349.1.40.011.1

swiing® revival 1/4" balls Ø 6.35 mm (22 pcs.)

Manufacturer: swiing® revival parts · Material: Steel · Area of application: Standard · Surface: hardened & ground · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Number of components: 22 pcs

swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch

Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29.02 mm · Thread length: 40.5 mm · Thread length: 50 mm · Ø inside: 12 mm · Height: 5.9 mm · Height: 9.9 mm · Width across flats SW: 19 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Ball bearing closed: Yes

swiing® revival bearing shell wheel Ø 29 mm | Puch

Manufacturer: swiing® revival parts · Material: Steel · Height: 9.2 mm · Ø outside: 29 mm · Surface: gas nitrided · Ø inside: 25.85 mm

swiing® ingenious bearing conversion kit cast front wheel | Piaggio Ciao, SI, Bravo, Grillo

Manufacturer: SKF · Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Ø outside: 14.9 mm · Ø outside: 20 mm · Ø outside: 32 mm · Ø inside: 11.25 mm · Ø inside: 15 mm · Total length: 53.5 mm · Width: 9 mm · Ball bearing closed: Yes

NSK 6202 ball bearing 15/35/11

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: NSK · Bearing type: Deep groove ball bearing · Width: 11 mm · Ø outside: 35 mm · Ø inside: 15 mm

swiing® revival 3/16" balls Ø 4.78 mm (26 pcs.)

Ø ball [inch] / [mm]: 3/16" (4.78 mm) · Manufacturer: swiing® revival parts · Number of components: 26 pcs · Material: Steel · Surface: hardened & ground · Area of application: Standard

NTN 6202 Ball bearing 15/35/11

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: NTN · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Material: Steel · Bearing type: Deep groove ball bearing · Width: 11 mm · Ø outside: 35 mm · Surface: blank · Ø inside: 15 mm · Ball bearing closed: No

Wheel bearing dust ring Ø 28 / 20 mm (with felt) | Piaggio Ciao, SI, Bravo, Boxer

Height: 3.6 mm · Ø outside: 28.25 mm · Ø inside: 19.75 mm · Piaggio OEM number: 124829

swiing® revival bearing cone M12x1

Manufacturer: swiing® revival parts · Color: black · Thread type: MF12x1 (fine pitch thread) · Height: 14.15 mm · Ø outside: 19.9 mm · Surface: gas nitrided · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 3/16" (4.78 mm)

NTN 6201 2RS wheel bearing 12/32/10 cast hub rear Grimeca

Stock number: 6201 · Manufacturer: NTN · Dust protection type: 2RS - NBR contact seal on both sides · Ø outside: 32 mm · Ø inside: 12 mm · Width: 10 mm · Ball bearing closed: Yes

FAG 16101 A 2RS wheel bearing 12/30/8

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 16101 · Inner ring width: 8 mm · Manufacturer: FAG · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Material: Plastic · Material: Steel · Area of application: Standard · Bearing type: Deep groove ball bearing · Width: 8 mm · Ø outside: 30 mm · Surface: blank · Ø inside: 12 mm · Ball bearing closed: Yes

swiing® ingenious wheel axle to bearing conversion kit cast rim | Piaggio Ciao

Manufacturer: swiing® ingenious parts · Material: Chrome steel (known as Nirosta®) · Material: Steel · Surface: galvanized (blue) · Thread type: MF11x1 (fine pitch thread) · Total length: 150 mm

Wheel bearing shell Ø 30 mm

Height: 13 mm · Material: Steel · Surface: galvanized (blue) · Ø inside: 25.9 mm · Ø outside: 30 mm · Ø bore: 15 mm · Ø Bundle: 33 mm

CUBE 6201 2RS wheel bearing 12/32/10 cast hub rear Grimeca

Stock number: 6201 · Width: 10 mm · Manufacturer: CUBE · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Ø inside: 12 mm · Ø outside: 32 mm

swiing® revival dust cover wheel bearing coaster brake (in the hub shell)

Manufacturer: swiing® revival parts · Height: 7.8 mm · Ø outside: 38 mm · Ø inside: 28 mm

CIF wheel axle set M11x1 x 165 mm front wheel galvanized | Piaggio Ciao, SI, Bravo

Manufacturer: CIF · Material: Steel · Ø shaft: 10.3 mm · Shank length: 18 mm · Thread type: MF11x1 (fine pitch thread) · Height: 2 mm · Height: 4 mm · Height: 10 mm · Surface: galvanized (blue) · Surface: galvanized (yellow) · Thread length: 73 mm · Total length: 165 mm · Width across flats SW: 15 mm · Width across flats SW: 17 mm · Ball bearing closed: No · Ø ball [inch] / [mm]: 1/4" (6.35 mm)

Triangular bearing plate galvanized | Piaggio Ciao, SI, Bravo

Manufacturer: Made in Italy · Material: Steel · Color: silver · Area of application: Standard · Width: 99 mm · Surface: galvanized (blue) · Number of fixing points: 2 pcs · Ø axle: 15 mm · Total length: 17.5 mm

swiing® ingenious triangular bearing plate Racing aluminum black | Piaggio Ciao, SI, Bravo

Manufacturer: swiing® ingenious parts · Material: Aluminum · Color: black · Area of application: Racing · Width: 101 mm · Thread type: M10x1.5 (standard thread) · Surface: anodized · Number of fixing points: 2 pcs · Total length: 13 mm · Thread length: 13 mm · Ø axle: 15 mm

swiing® revival dust cover driver back pedal type-A

Manufacturer: swiing® revival parts · Height: 4.2 mm · Ø outside: 28.2 mm · Ø inside: 20.4 mm · Sachs OEM no.: F1652 · Puch OEM number: 320.5.41.012.1

swiing® revival dust ring wheel bearing Ø 29.3 / 20.7 mm | Puch

Manufacturer: swiing® revival parts · Ø outside: 29.3 mm · Ø inside: 20.7 mm

Wheel bearing shell Ø 32 mm bright steel

Height: 14.25 mm · Material: Steel · Ø inside: 14 mm · Ø outside: 32 mm · Ø Bundle: 37 mm

swiing® ingenious wheel axle with bearing conversion kit cast wheel | Piaggio Ciao

Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Surface: anodized · Surface: galvanized (blue) · Diameter: 15 mm · Ø outside: 14.9 mm · Ø outside: 20 mm · Ø inside: 11.25 mm · Total length: 150 mm · Ball bearing closed: Yes

CUBE 6202 2RS ball bearing 15/35/11

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: CUBE · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing type: Deep groove ball bearing · Width: 11 mm · Ø outside: 35 mm · Ø inside: 15 mm · Ball bearing closed: Yes

swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch

Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes

swiing® ingenious wheel bearing 12/31/8 conversion spoke rim

Bearing cage: "-" Sheet steel cage ball-guided · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Groove ring: No · Material: Steel · Area of application: Standard · Bearing type: Deep groove ball bearing · Width: 8 mm · Ø outside: 31.01 mm · Surface: blank · Ø inside: 12 mm · Ball bearing closed: Yes

swiing® revival bearing cone M9.5x1

Manufacturer: swiing® revival parts · Material: Steel · Color: black · Thread type: MF9.5x1 (fine pitch thread) · Height: 13.8 mm · Ø outside: 19.55 mm · Surface: gas nitrided · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 1/4" (6.35 mm)

swiing® revival wheel bearing set M11x1

Manufacturer: swiing® revival parts · Material: Steel · Surface: gas nitrided · Thread type: MF11x1 (fine pitch thread) · Diameter: 17.95 mm · Ø outside: 29 mm · Ø inside: 25.85 mm · Height: 10.6 mm · Height: 14.15 mm · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 7/32" (5.56 mm)

swiing® ingenious bearing conversion kit front wheel | Pony GTX 521, Cross 521

Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Ø inside: 11.25 mm · Ball bearing closed: Yes

CIF ball ring front wheel | Piaggio Ciao, SI, Bravo, Boxer

Bearing cage: Plastic cage · Manufacturer: CIF · Bearing type: Ball ring

Bearing shell Grimeca front | Pony GTX Beta 521 (P8925)

Manufacturer: Pony · Material: Steel · Ø inside: 25.85 mm · Ø outside: 30.15 mm · Height: 12.9 mm · Pony OEM number: P8925

swiing® revival dust cover Ø 55 mm coaster hub body | Sachs / Puch / Zündapp Belmondo

Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Thickness: 4.5 mm · Ø inside: 46 mm · Ø outside: 55 mm

swiing® revival dust ring Ø 35 / 51 mm Driver

Manufacturer: swiing® revival parts · Ø inside: 35 mm · Ø outside: 51 mm · Height: 7.2 mm

Wheel bearing shell Ø 32 mm (with speedometer drive slot) NOS

Material: Steel · Height: 14 mm · Ø outside: 32 mm · Ø Bundle: 37 mm · Ø inside: 14 mm

SKF 6202 Ball bearing 15/35/11

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: CN (standard) · Bearing type: Deep groove ball bearing · Width: 11 mm · Ø outside: 35 mm · Ø inside: 15 mm

swiing® revival wheel axle set front wheel | Piaggio Ciao

Manufacturer: swiing® revival parts · Material: Steel · Thread type: MF11x1 (fine pitch thread) · Surface: galvanized (blue) · Total length: 150 mm · Ø ball [inch] / [mm]: 1/4" (6.35 mm)

CUBE 6202 2RS ball bearing 15/35/11 triangular bearing plate | Piaggio Ciao, SI, Bravo, Grillo

Bearing type: Deep groove ball bearing · Ø inside: 15 mm · Ø outside: 35 mm · Stock number: 6202 · Width: 11 mm · Manufacturer: CUBE · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides

Wheel axle set M11x1 x 153 front wheel spokes

Material: Steel · Surface: galvanized (blue) · Thread type: MF11x1 (fine pitch thread) · Total length: 150 mm

CUBE 6201 2RS wheel bearing 12/32/10 front & rear | Tomos

Stock number: 6201 · Width: 10 mm · Manufacturer: CUBE · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Ø inside: 12 mm · Ø outside: 32 mm · Tomos OEM number: 044225

Triangular bearing plate yellow galvanized | Piaggio Ciao, SI, Bravo, Grillo

Manufacturer: Quenching · Surface: galvanized (yellow)

swiing® revival wheel axle set Grimeca wheel hub cast wheel rear | Puch

Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 32 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 10 mm

swiing® ingenious wheel axle for bearing conversion kit Snowflake front wheel | Puch Maxi

Manufacturer: swiing® ingenious parts · Material: Chrome steel (known as Nirosta®) · Material: Steel · Surface: galvanized (blue) · Thread type: MF11x1 (fine pitch thread) · Total length: 154 mm

Wheel bearing shell Ø 32 mm | Sachs

Material: Steel · Ø outside: 32 mm · Ø bore: 14 mm · Ø Bundle: 37 mm · Height: 14 mm

swiing® ingenious bearing conversion kit Snowflake front wheel | Puch Maxi

Manufacturer: SKF · Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Ø inside: 11.25 mm · Ball bearing closed: Yes

swiing® ingenious wheel axle for bearing conversion kit Snowflake rear wheel | Puch Maxi

Manufacturer: swiing® ingenious parts · Material: Chrome steel (known as Nirosta®) · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Total length: 185 mm